Flying Wing (Gliding type)

Step 1: 
Lay the paper out on the table with the long side as shown. Fold in half to make a crease up the center..Then, fold the corners down to the crease...

Step 2: 
Take the top point and fold it all the way down to the bottom edge... Then un-fold so you've made a crease

Step 3: 
With the model flat again, fold the tip down to the crease line you just made...

Step 4: 
Next fold the top along the crease you've already made.. All we're doing here is building up the leading edge to get good flying balance and a tough little nose. This is one of the safer fold n fly models and perfect for little kids... Fly responsibly!!

Step 5: 
Yet Another fold.,,,and again, to the crease. We are creating a heavy nose so your wing will fly better

Step 6: 
Grasp the outer edges and fold the airplane back over itself..When you make this kind of fold, it's called a "mountain fold"

Step 7: 
Fold the 'wings' down keeping the 'fuselage' depth about one inch... Staple the fuselage together if you wish.

Step 8: 




Try adding a small paper clip to the nose of your flying wing. Do some experimenting with slight bending of the flying surfaces to get you wing to do variations with its gliding effects. 

Paper Helicopter

Step 1 :
Get an index card or Paper (a 3 by 5card works best but you can use any rectangular index card or even paper).

Step 2 :
Fold the card or paper in half and unfold

Step 3:

 Cut about half way down the crease that you folded.

Step  4 :

Now cut about 1/3 through the paper laterally a little below your first cut from the long edge.

Step 5 :

Fold both of the sections you made in step 4 in like these pictures

Step 6 :

Fold the cuts you made in step 1 in opposite directions on either side, forward and backward. Than add a paperclip on the very bottom of the helicopter and you're done! Your helicopter should look like the picture in the introduction.

Drop from your hand from as high a place you can and watch it spin as it falls

WEDGE DART PLANE

step 1.
Fold the paper vertically (length wise) and
then un-fold it to make a crease up the middle..

step 2. 

Fold the outer corners into the center crease. This is how a lot of these Fold n' Fly models start out..

step 3.

Fold the triangular top down as shown.

step 4. 

Fold the upper corners down with the corners meeting on the crease line. After this fold the airplane back on itself as shown in STEP 5

step 5.

Plane is folded back on itself..

step 6.

Next we need to make the Wedgie's wings. Simply fold  the top edges down

step 7.
With the wings ice and horizontal, staple the fuselage together anywhere along the fuselage.. Then to give your model a good serious ballast in the nose, a small paper clip is jsut the ticket..

The great feature of the 'dart wedge' is that the flying surfaces are so easy to adjust. If the model dives, bend the trailing surface upward just a tab and watch it stretch out that glide..

Basic paper plane model

1. step 1

make a mark about an angle of 45 degree in a A4 for any rectangular sheet like shown in figure

2. Step 2

after folding as in step 1... now do one more cross fold about 30 degrees and ake one more folding

3. step 3

bend as per step 1 and step 2... you will get a pyramid shape compressed type,,, now you are closer to finish your basic paper plane

4. Step 4

cross bend the folded paper plane as shown in figure... now your fllight is ready but important thing wing is missing... now its time to add an wing and make our plane to fly...

5. Step 5

make a wing by folding the fuselage(main body) of our paper plane...

now you have successfully made your basic paper plane...fly in air and find how much distance it covers,,,

bigger your Paper plane wings,, more your stability and Range...

technical details will be posted on next blog ...

thank you